Good Clean-In-Place And CIP / SIP Multi Lobe Pump For Oil Sludge
Lobe Pump Overview
Lobe pumps are used in a variety of industries including pulp and
paper, chemical, food, beverage, pharmaceutical, and biotechnology.
They are popular in these diverse industries because they offer
superb sanitary qualities, high efficiency, reliability, corrosion
resistance, and good clean-in-place and sterilize-in-place
(CIP/SIP) characteristics.
Specifications:
| ACCUVON | rate of flow
l/rev | flow
(m³/h) | pressure
(Mpa) | speed
rpm | Flange diameter
DN mm | power
Kw |
| AC25 | 0.196 | 0.1-7 | 0-1.2 | 10-600 | DN25 | 0.75-5.5 |
| AC50 | 0.392 | 0.2-14 | 0-1.0 | 10-600 | DN50 | 1.1-5.5 |
| AC75 | 0.588 | 0.3-21 | 0-0.6 | 10-600 | DN50 | 1.1-5.5 |
| AP80 | 1.125 | 0.6-400 | 0-1.8 | 10-600 | DN80 | 3-22 |
| AP100 | 1.875 | 1.1-66 | 0-1.4 | 10-600 | DN100 | 3-22 |
| AP120 | 2.864 | 1.7-103 | 0-1.0 | 10-600 | DN100 | 3-22 |
| AP140 | 3.714 | 2.2-133 | 0-0.6 | 10-600 | DN125 | 7.5-22 |
| AF125 | 4.566 | 2.7-164 | 0-1.6 | 10-600 | DN125 | 11-55 |
| AF150 | 6.828 | 4-246 | 0-1.2 | 10-600 | DN150 | 11-55 |
| AF200 | 9.456 | 5.5-340 | 0-0.8 | 10-600 | DN200 | 11-55 |
| AX250 | 12.5 | 7.5-487 | 0-2.5 | 10-650 | DN250 | 22-315 |
| AX300 | 25 | 15-975 | 0-1.0 | 10-650 | DN300 | 30-315 |
| AX350 | 37.5 | 22.5-1463 | 0-0.6 | 10-650 | DN350 | 45-315 |
| AX450 | 50 | 30-1950 | 0-0.4 | 10-650 | DN450 | 55-315 |
| AX350D | 75 | 45-2926 | 0-0.6 | 10-650 | DN350*2 | 90-450 |
| AX450D | 100 | 60-3900 | 0-0.4 | 10-650 | DN450*2 | 110-600 |
Note: Above flange is regular for each model, besides we also offer
various flange connection according to your requirements
1. Tested medium in the table: water.
2. Speed, flow rate, electrical power and pressure will be
according to different liquid properties.
3. Port size can be changed as needed.
4. ACCUVON reserves the right to change specifications without
prior notification.
Function
Rotor
Lobe pump manufacture use high precision 5-axis CNC machining. Our
rotor perfectly seal with the inlets and outlets chamber, pump
suction ability can reach to 9 meters. The material of the rotor
can be selected according to the characteristics of conveying
medium. We have many kinds of rotor material for selection,
including anti-wear elastomers, hard steel, stainless steel and
etc.
Space Occupied
Our lobe pumps design is compact, can be installed in extremely
limited space. The design of flange and placement of the motor can
be adjusted to fit for the customer's space constraints.
Pump Body
Pump body choose inblock casting, the error is minimal. Body
material can be cast iron and stainless steel. Chamber inside have
replaceable protective liner. The liner surface can be hardened to
increase wear resistance.
Simple Maintenance
Our lobe pump is unilateral shaft support design, fluid chamber can
be quickly disassemble. Rotors and other accessories can be
replaced in a few minutes without remove the pump inlet and outlet
pipes. Also lobe pump have few wearing parts, it make lobe pump
lower shutdown time and lower using cost.
Operating Efficiency
Very high efficiency, about 60% to 85%.
The Particles Size
Lobe pump have wide fluid chamber, no block problem.
Self-priming and Dry Running
Lobe pump have good self-priming ability, reach to 9.5m, and can
allow a certain time dry running.
Quality inspection photos
